Home / Technical Support / Service
Maintenance Storage Of Rubber Boats
Assembly And disassembly ​​​​​​​
Operation Manual And Storage​​​​​​​
  • Step 1 Assemble

    1. The inflatable rubber boat should be installed and inflated to remove all sharp things.
    2. Unroll the inflatable boat and stretch it on the ground.
    3. Install the valve in the appropriate position, ensure that the cover gasket is in the appropriate position, and install the valve slide lock on each valve.
    4. When used for the first time, the foot inflator should be installed on the air valve, one at a time, and filled with gas to ensure the balance of air pressure between the air bags. When full of air, release the valve and let off about 1/2 of the air. Then turn the air valve and continue to install. Note: The keel should not be inflated until the bottom plate is installed.
    5. If the boat has previously been inflated, attach the pedal inflators to each valve, one at a time, and inflate until the bag capacity is 1/2.

  • Step 2 Disassemble

    1. Release all air valves to deflate.
    2. Remove your seat.
    3. Remove the side connection from the bottom plate.
    4. Use the pedal inflator as an inflator to discharge the remaining gas in each airbag.
    5. With the bottom of the boat facing down, tuck the hull over the side of the boat into the boat, roll up the hull from either side and load it into the backpack along with the inflator and hose.

  • Operation manual and storage 

    1. Each boat owner shall wear appropriate clothing and be equipped with life jackets and other personal life-saving equipment of qualified quality. 
    2. The load must be evenly distributed. If you are using an outboard motor with a very light load, do not accelerate suddenly. The wrong operation of the operator may have an adverse effect on the stability and handling performance of the ship. 
    3. Please equip the boat with an outboard motor to the extent permitted by the performance indicators. Please do not overload. 
    4. After use, the boat and all its accessories should be scrubbed with a mild cleaning agent and washed with clean water. After drying, all parts are packed into a portable bag before storage. This will prevent mildew and bacteria. 
    5. It is best to check the wood accessories for damage and deformation. Scratches and wear on its surface should be repaired with Marine varnish. 
    6. If you want to keep the boat in a newer condition, pay attention to storing the boat in a dry and cool place to avoid long-term sunlight exposure. 
    7. In order to avoid damage to the boat during storage, do not place heavy objects on it. 

  • Operation Manual And Storage

    1. Each boat owner shall wear appropriate clothing and be equipped with life jackets and other personal life-saving equipment of qualified quality.
    2. The load must be evenly distributed. If you are using an outboard motor with a very light load, do not accelerate suddenly. The wrong operation of the operator may have an adverse effect on the stability and handling performance of the ship.
    3. Please equip the boat with an outboard motor to the extent permitted by the performance indicators. Please do not ove

  • Operation Manual And Storage

    4. After use, the boat and all its accessories should be scrubbed with a mild cleaning agent and washed with clean water. After drying, all parts are packed into a portable bag before storage. This will prevent mildew and bacteria.
    5. It is best to check the wood accessories for damage and deformation. Scratches and wear on its surface should be repaired with Marine varnish.
    6. If you want to keep the boat in a newer condition, pay attention to storing the boat in a dry and cool place to avoid long-term sunlight exposure.
    7. In order to avoid damage to the boat during storage, do not place heavy objects on it.

    3. Maintenance procedures
    1. Small cracks, wounds, and holes
    1-1. Repair leaks or small holes smaller than 1/2 inch (12.7mm) by covering them with a disc with a minimum diameter of 3 inch (76.2mm).
    1-2. The surface of the hull and the surface of the material to be repaired must be dry and clean.

Maintenance Procedures

  • Small Cracks, Wounds, And Holes
    1-1. Repair leaks or small holes smaller than 1/2 inch (12.7mm) by covering them with a disc with a minimum diameter of 3 inch (76.2mm).

    1-2. The surface of the hull and the surface of the material to be repaired must be dry and clean.

    1-3. Apply a thin layer of adhesive to the hull damage and to the surface of the repair disc. Apply three times, five minutes apart. After applying the glue for the third time, wait 10-15 minutes, then glue the repair disc to the damaged part of the hull, and use a hard roller to press the repair disc to the hull to make it tight.

    1-4. It needs to stand for more than 24 hours before it can be reinflated.
  • Major repairs (surfaces, joints, diaphragms, beams) We recommend that you contact your distributor for repairs.


We also according to the requirements of customers to use and the aspects to provide customized services, to achieve customer personalized demand.




 No. 38 Xianshan East Road, Xiazhuang Street, Qingdao, Shandong, China
 +86-195-0615-9507
​Copyright ©2023 Qingdao Joymax Yacht Co.,Ltd All rights reserved  Support By : Leadong